Passing the HP HPE6-A79 exam is not a simple matter. So why choose Lead4Pass HPE6-A79 exam dumps? https://www.leads4pass.com/hpe6-a79.html (PDF + VCE).
Because lead4Pass is a trusted and old store! Over the years we have served tens of thousands of users! They all passed the exam successfully! We have the best reputation!
Is the leader of the industry! To pass the HP HPE6-A79 exam, you only need to choose the Lead4Pass HPE6-A79 exam dumps to ensure that you successfully pass the exam!
Lead4pass HPE6-A79 exam dumps contain two modes: PDF and VCE Software! You can choose at will according to your study habits!
This site shares a part of HP HPE6-A79 exam practice questions for free, you can practice the test online.
Share part of HP HPE6-A79 exam PDF for free
The free HP HPE6-A79 exam PDF is part of the Lead4Pass HPE6-A79 exam dumps. Download it for free at Google Drive.
HP HPE6-A79 exam questions online practice test
QUESTION 1
Refer to the exhibit.
Based on the output shown in the exhibit, which channel offers the highest quality?
A. Channel 1
B. Channel 6
C. Channel 11
D. Channel 14
Correct Answer: B
QUESTION 2
An organization has several RAPs at different locations that broadcast two SSIDs. The internet-only SSID is in
bridge/always mode, and the corporate SSID is in split-tunneling/standard mode. The network administrator deploys 10 more RAPs in different locations.
Users can successfully connect to the corporate SSID that is propagated by a RAP at a remote location. However, they
report that it takes too long to access public internet websites.
What is one part of the configuration that should be checked by the network administrator to verify this RAP
deployment?
A. User roles policies
B. IP pool
C. Operating mode
D. Assigned VLAN
Correct Answer: A
QUESTION 3
Refer to the exhibits. Exhibit 1
Exhibit 2
Exhibit 3
A network administrator wants to allow contractors to access the corporate WLAN named EmployeesNet with the
contractor role in VLAN 40. When users connect, they do not seem to get an IP address. After some verification checks,
the network administrator confirms the DHCP server (10.254.1.21) is reachable from the Mobility Controller (MC) and
obtains the outputs shown in the exhibits.
What should the network administrator do next to troubleshoot this problem?
A. Permit UDP67 to the contractor role.
B. Remove the IP address in VLAN 40.
C. Configure the DHCP helper address.
D. Confirm there is an IP pool for VLAN 40.
Correct Answer: A
QUESTION 4
Refer to the exhibit.
A network administrator adds a Mobility Controller (MC) in the /mm level and notices that the device does not show up in the managed networks hierarchy. The network administrator accesses the CLI. executes the show switches
command, and obtains the output shown in the exhibit.
What is the reason that the MC does not appear as a managed device in the hierarchy?
A. The network administrator added the device using the wrong Pre-Shared Key (PSK).
B. The network administrator has not moved the device into a group yet.
C. The digital certificate of the MC is not trusted by the MM.
D. The IP address of the MC does not match the one that was defined in the MM.
Correct Answer: D
QUESTION 5
Refer to the exhibit.
A network administrator wants to allow contractors to access the WLAN named EmployeesNet. In order to restrict
network access, the network administrator wants to assign this category of users to the contractor user role. To do this,
the network administrator configures ClearPass in a way that it returns the Aruba-User-Role with the contractor value.
When testing the solution, the network administrator receives the wrong role.
What should the network administrator do to assign the contractor role to contractor users without affecting any other
role assignment?
A. Check the Download role from the CPPM option in the AAA profile.
B. Set contractor as the default role in the AAA profile.
C. Create Contractor firewall role in the M.
D. Create server deviation rules in the server group.
Correct Answer: A
Reference: https://www.arubanetworks.com/techdocs/ClearPass/6.7/Aruba_DeployGd_HTML/Content/Aruba%20Contro
ller%20Configuration/AAA_profile_adding.html
QUESTION 6
A company plans to build a resort that includes a hotel with 1610 rooms, a casino, and a convention center. The
company is interested in a mobility solution that provides scalability and a service-based approach, where they can rent the WLAN infrastructure at the convention center to any customer (tenant) that hosts events at the resort.
The solution should provide:
Seamless roaming when users move from the hotel to the casino or the convention center
Simultaneous propagation of the resort and customer-owned SSIDs at the convention center
Null management access upon resort network infrastructure to the customers (tenants)
Configuration and monitor rights of rented SSIDs to the customers (tenants)
Which deployment meets the requirements?
A. Deploy an MM-MC infrastructure with multizone AP\’s, with one zone for tenant SSIDs.
B. Deploy IAPs along with AirWave, and deploy role-based management access control.
C. Deploy IAPs with zone-based SSIDs and manage them with different central accounts.
D. Deploy an MM-MC infrastructure and create different hierarchy groups for MCs and APs.
E. Deploy IAPs and manage them with different central accounts.
Correct Answer: E
QUESTION 7
A company with 535 users deploys an Aruba solution with more than 1000 Aruba APs, two 7220 Mobility Controllers,
and a single Mobility Master (MM) virtual appliance at the campus server farm. The MCs run a HA Fast failover group in
dual mode and operate at 50% AP capacity.
If there is an MM or MC failure, the network administrator must ensure that the network is fully manageable and the MC load does not exceed 80%.
What can the network administrator do to meet these requirements?
A. Place the APs in the same hierarchy level.
B. Create a cluster with AP load balancing.
C. Enable oversubscription in the HA group.
D. Add an MC and an MM in the server farm.
E. Add an MM and enable DC redundancy.
F. Place the APs in two different AP-Groups.
Correct Answer: E
QUESTION 8
Refer to the exhibit.
A network administrator is evaluating a deployment to validate that a user is assigned the proper role and reviews the
output in the exhibit. How is the role assigned to the user?
A. The MC assigned the role based on Aruba VSAs.
B. The MC assigned the machine authentication default user role.
C. The MC assigned the default role based on the authentication method.
D. The MC assigned the role based on server derivation rules.
Correct Answer: C
QUESTION 9
Refer to the exhibits.
A network administrator deploys User-Based Tunneling (UBT) in a corporate network to unify the security policies
enforcement. When users authenticate with 802.1X, ClearPass shows Accept results and sends the Aruba-User-Role
attribute as expected. However, the AOS-CX based switch does not seem to build the tunnel to the Mobility Controller
(MC) for this user.
Why does the switch fail to run UBT for the user?
A. The switch has not been fully associated with the MC.
B. ClearPass is sending the wrong Vendor ID.
C. The switch is not configured with the gateway role.
D. ClearPass is sending the wrong VSA type.
E. The switch is not configured with the port-access role.
Correct Answer: B
QUESTION 10
Refer to the exhibit
A network administrator deploys a standalone Mobility Controller (MC) and configures some VAPs within the CAMPUS
AP group. The network administrator realizes that none of the VAPs are being broadcasted.
Based on the output shown in the exhibit, what should the network administrator do to solve this problem?
A. Install MC-VA licenses, then install PEF licenses and enabled the PEF feature.
B. Install MC-VA licenses, then reprovision the APs.
C. Install MM licenses, then install PEF licenses and enable the PEF feature.
D. Install MM licenses and install MC-VA licenses, then install RFP licenses.
Correct Answer: D
QUESTION 11
A joint venture between two companies results in a fully functional WLAN Aruba solution. The network administrator
uses the following script to integrate the WLAN solution with two radius servers, radius1 and radius2.
While all users authenticate with [email protected] type of credentials, radius1 has user accounts with the
domain name portion. Which additional configuration is required to authenticate corp1.com users with radius1 and corp2 users with radius2?
A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: A
QUESTION 12
Refer to the exhibits. Exhibit 1
Exhibit 2
A network administrator adds a new Mobility Controller (MC) to the production Mobility Master (MM) and deploys APs
that start broadcasting the employee SSID in the West Wing of the building. Suddenly, the employees report client
disconnects. When accessing the MM the network administrator notices that the MC is unreachable, then proceeds to
access the MC\’s console and obtains the outputs shown in the exhibits.
What should the network administrator do next to solve the current problem?
A. Open a TAC case and send the output of the tar crash.
B. Kill two zombie processes then reboot the MC.
C. Verify the license pools in the MM.
D. Decommission the MC from the MM and add it again.
Correct Answer: C
QUESTION 13
Refer to the exhibit
A 7008 Branch Office Controller (BOC) is deployed in a remote office behind a core router. This core does not support
802.1q encapsulation. The Mobility Controller (MC) is the gateway for two tunneling mode SSIDs, as shown in the
exhibit. Which two different configuration options ensure that wireless users are able to reach the branch network
through the router? (Choose two.)
A. Configure all ports of the BOC as access ports on the controller VLAN, and change the gateway of clients to the core
router IP.
B. Configure the uplink of the BOC as an access port on the controller VLAN and add static routes in the router for the
SSID VLAN subnets.
C. Configure the uplink of the BOC as a trunk port that permits the controller and the SSID VLANs. The controller VLAN
must be native.
D. Configure the uplink of the BOC as an access port on the controller VLAN and enable NAT for the SSID VLANs.
E. Configure the uplink of the BOC as a trunk port, tagging the controller and the SSOD VLANs, and enable NAT for the
SSID VLANs.
Correct Answer: BE
Summarize:
HP HPE6-A79 exam questions and answers have been updated to ensure they are true and valid.
Free sharing of HP HPE6-A79 exam practice questions can improve your exam success rate.
To pass the exam 100% smoothly, please click Lead4Pass HPE6-A79 dumps https://www.leads4pass.com/hpe6-a79.html (total question: 55 Q&A). Lead4Pass contains complete exam questions and answers! All exam questions and answers are valid immediately.
ps.
The free HP HPE6-A79 exam PDF is part of the Lead4Pass HPE6-A79 exam dumps. Download it for free at Google Drive.